View 3B20_1199450.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AC Strain Gage, Torque Transducer Input 3B20
FEATURES
Interfaces, amplifies, & filters signals from 4-arm AC bridge transducer signals ranging between 1.5mV rms & 150mV rms. Module provides an AC excitation voltage of 2V rms to 10V rms at frequencies between 1kHz & 10kHz.. Module provides simultaneous precision voltage and current outputs. Module circuitry can withstand 130v rms at its current output terminals without damage. All 3B20 series modules are mix-and-match and Hot Swappable
FUNCTIONAL BLOCK DIAGRAM
Figure 1. 3B20 Functional Block Diagram
APPLICATIONS
Industrial signal conditioning Industrial signal isolation Industrial signal filtering
Output modules accept 0 to +10V (or +10V) single-ended signals and provide an isolated 4-20 mA (or 0-20 mA) process signal. All modules feature a universal pin-out and may be readily hot-swapped under full power and interchanged without disrupting field wiring. The Analog Devices 3B Series Signal Conditioning Subsystem is designed to easily handle signal conditioning problems in measurement and control applications. Some typical uses are in microcomputer-based data acquisition systems, programmable controllers, analog recorders, dedicated control systems, and any other applications where monitoring of temperature, pressure, flow and analog signals are required. Since each input module features two simultaneous outputs, the voltage output can be used to provide an input to a microprocessor-based data acquisition or control system while the current output can be used for analog transmission, operator interface, or an analog backup system. Each input module is a single-channel signal conditioner which plugs into a socket on the backplane and accepts its signal from the input screw terminals. All input modules provide input protection, amplification and filtering of the input signal, accuracy of +0.1%, low drift of +1 uV/oC (low-level input modules), and feature two high-level analog outputs that are compatible with most process instrumentation. The isolated input modules also provide +1500 V peak isolation. The choice of a specific 3B module depends upon the type of input signal. Input modules are available to accept millivolt, volt, process current, thermocouple, RTD, AC and DC strain gage, frequency and LVDT inputs. The voltage output of each module is available from the system I/O connector while the current output is available on the output screw terminals.
PRODUCT OVERVIEW
The 3B Series of Signal Conditioning I/o Subsystems provide a low-cost, versatile method of transferring analog transducer signals to a data acquisition, monitoring or control system without the inherent noise, non-linearity, drift and extraneous voltages. The modules are designed to directly accept analog signals from Thermocouples, RTD's, AC and DC Strain Gages, Torque Transducers, Frequency Transducers, LVDTs, millivolt or process current signals. The modules amplify, isolate, linearize and convert the transducer output signals to standardized analog inputs for high-level analog I/O subsystems. The 3B Series Subsystem consists of a 10" relay rack with universal mounting backplane and a family of plug-in (up to 16 per rack) input and output signal conditioning modules. Eight and four channel backplanes are also available. Each backplane incorporates screw terminals for sensor inputs and current outputs and a 26-pin connector for high-level singleended voltage outputs to the user's equipment. The input modules feature complete signal conditioning circuitry optimized for specific sensors or analog signals and provide two simultaneous high-level analog outputs: 0 to +10V (or +10V) and 4-20 mA (or 0-20 mA).
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective companies.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. www.analog.com Tel: 781.329.4700 Fax: 781.326.8703 (c) 2004 Analog Devices, Inc. All rights reserved.
3B20 GENERAL DESCRIPTION
The 3B20 is a wideband single-channel signal-conditioning module which interfaces 4-arm AC bridge transducer signals ranging between 1.5mV rms and 150mV rms, providing simultaneous precision voltage and current outputs. In addition, the module provides an AC excitation voltage of 2V rms to 10V rms at frequencies between 1kHz and 10kHz. The module withstands 130V rms at its current output terminals without damage thereby shielding computer-side circuitry from fieldside over-voltage conditions. The 3B20 is a plug-in, mix-andmatch, hot-swappable module and is easily field calibrated via front-panel zero and span adjustments for both voltage and current outputs. 3B Series Custom-Ranging Program - Externallyprogrammable Model 3B20-00, enables the user to configure a special input range, including tare weight suppression, by using the optional plug-on AC1310 ranging card, which houses usersupplied resistors to determine zero and span. To facilitate . selecting resistors, a Windows program, 3B-CUSTOM, calculates resistor values based on the user-desired input/output ranges. The 3B20 input and AC bridge excitation output terminals are protected for up to 130V rms. The excitation amplitude and frequency can be specified with the Model 3B20 CUSTOM or user configured with Model 3B20-00 and an optional plug-on Model AC1310 ranging card. Both the voltage and current outputs can be independently adjusted for a minimum of +1V for the zero and 25% of the span range with front-panel useraccessible potentiometers. In addition, phase shifts of up to 37.25o between excitation signal and the output signal from the strain gauge or torque transducer can be compensated via frontpanel screw terminal adjustments.
.
Figure 2
Rev. 0 | Page 2 of 8
3B20
3B20 Models Available
Model 3B20-00 3B20-01 3B20-Custom
1 2
Excitation Voltage Externally Programmable2 5 V rms *
Excitation Frequency Externally Programmable2 3 kHz *
Input Range Externally Programmable2 20 mV rms *
Sensitivity Externally Programmable2 2 mV rms/V *
Output Ranges1 -10 V to +10 V & 0 mA to 20 mA -10 V to +10 V & 0 mA to 20 mA *
Output current range may be user programmed to 4 mA to 20 mA using jumper supplied. Requires AC1310 ranging card. * Custom Input/Output ranges are available. Refer to configuration guide.
3B20 Specifications (typical @ +25C and 15 V dc, and +24 V dc Power)
Description Input Range Standard Range Custom Ranges Refer to Model Table Vin = 1.5 mV rms to 150 mV rms Vexc = 2 V rms to 10 V rms Vexc freq. = 1 kHz to 10 kHz Output Range Voltage (RL > 2 K) Current (RL = 0 to 850) With Input Overload Accuracy Initial @ +25C Nonlinearity
2 2 1
Model 3B20
-10 V to +10 V 4 mA to 20 mA or 0 mA to 20 mA 40 mA, maximum
0.1% Span 0.05% Span Stability vs. Temperature
Voltage Output Zero Span Current Output3 Zero Span 25 ppm of Span/C 25 ppm of Reading/C Bridge Excitation Voltage
4
0.005% of Span/C 0.01% of Span/C
2 V rms to 10 V rms 2.5% 1 kHz to 10 kHz, 15% Up to 20 mA rms, minimum < 0.5%
4
Voltage, tolerance Frequency4 Drive Harmonic Distortion Span Calibration Adjustment Range
25% of span, minimum Rev. 0 | Page 3 of 8
3B20
Zero Calibration Adjustment Range4 Phase Adjustment Range
5
1 V, minimum 0 to 4.25 minimum @ 1 kHz 0 to 14 minimum @ 3.28 kHz 0 to 37.25 minimum @ 10 kHz +10 nA 100 M 100 Hz 200 ms
Input Bias Current Input Resistance Bandwidth, -3 dB Output Rise Time, 10% to 90% Span
Input Protection, Signal and Excitation Voltage Continuous Transient Voltage Output Protection Current Output Protection 130 V rms maximum ANSI/IEEE C37.90.1-1989 Continuous Short to Ground 130 V rms, continuous Power Supply Voltages 5 15 V dc Supplies Rated Operation Current Sensitivity +24 V dc Loop Supply Rated Operation Current Sensitivity Mechanical Dimensions +13.5 V dc to +30 V dc +27 mA @ lout = 20 mA 0.001% span/V 3.15" x 3.395" x 0.775" (80.0 mm x 86.2 mm x 19.7 mm) Environmental Temperature Range Rated Performance Storage Relative Humidity, 24 hours RFI Susceptibility
1 2 3
(13 V dc to 18 V dc) 65 mA 0.03% span/V
-25C to +85C -55C to +85C 0 to 95% @ +60C non-condensing 0.5% Span error @ 400 MHz, 5 Watt, 3 ft
For a 0 mA to 20 mA range, a typical minimum output current is 10 A. Includes the combined effects of repeatability, hysteresis, and nonlinearity. With respect to the voltage output. 4 A wide range of custom zero suppression and span is available with the 3B20-00 model, using the AC1310 ranging card. 5 +24 V dc loop power is required for driving the current output at loads up to 850. If a current output load of 400 or less is applied, +15 V dc is sufficient for loop power. If only voltage output is used, loop power is not required. Specifications subject to change without notice.
Rev. 0 | Page 4 of 8
3B20 PIN CONFIGURATIONS AND FUNCTIONAL DESCRIPTIONS
Figure 3 3B20 Input Field Connections
Table 1. Pin Function Descriptions--
Pin No. 1 2 3 4 Description +EXC HI LO -EXC
Figure 4 . Model 3B Series Module, with pin-out assignments.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
Rev. 0 | Page 5 of 8
3B20 OUTLINE DIMENSIONS
Figure 5. Outline Dimensions
Rev. 0 | Page 6 of 8
3B20 NOTES
Rev. 0 | Page 7 of 8
3B20 NOTES
(c) 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective companies. D05092-0-9/04(0)
Rev. 0 | Page 8 of 8

▲Up To Search▲

Price & Availability of 3B20

	To Download 3B20 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .